Flange Yokes
Filters: JOINT ANGLE = 0, CENTERLINE TO FACE = 1.625, | PART NUMBER | SERIES | PILOT TYPE | PILOT DIA. | BOLT CIRCLE DIA. | BOLT HOLE COUNT | BOLT HOLE DIA. | C/L TO FACE | SWING DIA. | JOINT ANGLE | NOTES | VEHICLE CLASS | BRAND |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
3-2-1819 |
1410 | F | 2.000 | 4.250 | 4 | 0.500 | 1.625 | 5.240 | 0 | Square pattern, Ford trucks with hole in center. | LD | Spicer |
| P2-2-949 |
1330 | F | 2.000 | 3.500 | 4 | 0.484 | 1.625 | 4.469 | 0 | Sq Bolt Pattern / Early version of 2-2-1369. Only difference is the bolt circle. | LD | PTI |
| 3-2-1619 |
1350 | F | 2.000 | 4.250 | 4 | 0.410 | 1.625 | 5.250 | 0 | M12-1.75 holes, square pattern | LD | Spicer |
| 3302-1369 |
1330 | F | 2.000 | 4.250 | 4 | 0.500 | 1.625 | 5.250 | 0 | Square pattern, used at rear end from early 90's and up. | LD | PTI |
| T2-2-1369A |
1330 | F | 2.000 | 4.250 | 4 | 0.500 | 1.625 | 5.250 | 0 | 6061-T6 Forged Aluminum / 45% Lighter | LD | PTI |
| T3-2-1579A |
1350 | F | 2.000 | 4.250 | 4 | 0.500 | 1.625 | 5.250 | 0 | 6061-T6 Forged Aluminum / 47% Lighter | LD | PTI |
| T2-2-949A |
1330 | F | 2.000 | 3.500 | 4 | 0.484 | 1.625 | 4.469 | 0 | 6061-T6 Forged Aluminum / 37% Lighter | LD | PTI |
| 3502-1579 |
1350 | F | 2.000 | 4.250 | 4 | 0.500 | 1.625 | 5.250 | 0 | Square pattern, fits Ford 8.8 and 9.75 all years. This flange has a large hole for clearance | LD | PTI |
| 4102-1819 |
1410 | F | 2.000 | 4.250 | 4 | 0.500 | 1.625 | 5.240 | 0 | Square pattern, Ford trucks with hole in center. | LD | Spicer |
| 3502-1619 |
1350 | F | 2.000 | 4.250 | 4 | 0.410 | 1.625 | 5.250 | 0 | M12-1.75 holes, square pattern | LD | PTI |
| 3302-949 |
1330 | F | 2.000 | 3.500 | 4 | 0.484 | 1.625 | 4.469 | 0 | Square pattern | LD | PTI |
| 3502-1580 |
1350 | F | 2.000 | 4.250 | 4 | 0.500 | 1.625 | 5.250 | 0 | Square pattern. This flange has a larger hole for pinion nut clearance | LD | PTI |
| 3502-216 |
1350 | F | 2.162 | 3.937 | 4 | 0.489 | 1.625 | 4.960 | 0 | Dodge, Square | LD | PTI |
| 3302-1879-1 |
1330 | F | 2.162 | 3.937 | 4 | 0.489 | 1.625 | 4.960 | 0 | Dodge 0.305" shorter then Dana 2-2-1879 | LD | PTI |
| 2-2-1609 |
1310 | M | 2.375 | 3.125 | 4 | 0.406 | 1.625 | 3.875 | 0 | Rec Bolt Pattern | LD | Spicer |
| 3-2-1699 |
1350 | F | 2.680 | 4.250 | 4 | 0.410 | 1.625 | 5.250 | 0 | Sq Bolt Pattern / Bolt holes are M12-1.75 threaded. Ford 4x4 Trucks usually located at the rear output of the transfer case. If you want to convert the driveshaft to a CV type use our part number 3502-42. | LD | Spicer |
| 3502-1699 |
1350 | F | 2.680 | 4.250 | 4 | 0.410 | 1.625 | 5.250 | 0 | Sq Bolt Pattern / Bolt holes are M12-1.75 threaded. Ford 4x4 Trucks usually located at the rear output of the transfer case. If you want to convert the driveshaft to a CV type use our part number 3502-42. | LD | PTI |
